Muratec MFX-1700 Specifications Page 39
- Page / 232
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-9
Machine Parameter B:7
Switch
Initial
Setting
Adjust Usage/Comments
7 0
6 0
5 0
4 0
3 0
2 0
1 0
0 0
Leading edge document
margin adjustment
(ADF)
Adjusts the leading edge
margin from Document
Sensor 2 (DS2) to the start of
the scanning position.
Each setting changes
by 0.0847mm.
Note: These values are
factory set and should not be
adjusted unless instructed by
a Muratec technical
representative.
Switch 76543210 Settings
10111111 -5.3361 mm
10111110 -5.2514 mm
10000010 -0.1694 mm
10000001 -0.0847 mm
00000000 0.00 mm
00000001 0.0847 mm
00000010 0.1694 mm
00111110 5.2514 mm
00111111 5.3361 mm
Machine Parameter B:8
Switch
Initial
Setting
Adjust Usage/Comments
7 0
6 0
5 0
4 0
3 0
2 0
1 0
0 0
Trailing edge document
margin adjustment.
(ADF)
Adjusts the document feed
after the trailing edge of a
document passes
Document Sensor 2 (DS2).
Each setting changes
by 0.085mm.
Note: These values
are factory set and should
not be adjusted unless
instructed by a Muratec
technical representative.
Switch 76543210 Settings
10111111 -5.3361 mm
10111110 -5.2514 mm
10000010 -0.1694 mm
10000001 -0.0847 mm
00000000 0.00 mm
00000001 0.0847 mm
00000010 0.1694 mm
00111110 5.2514 mm
00111111 5.3361 mm
Machine Parameter B:9 ∼
∼∼
∼ C:9 --- Factory use only
- MFX-1300/MFX-1700 1
- MFX-1200/MFX-1600 1
- Table of Contents 3
- Section 6 Options 5
- Safety Information 7
- Section 1 9
- General Description 9
- 1.2 Specifications 10
- Section2 13
- Machine Composition 13
- MFX-1200/1300 14
- Connection Diagram (2/2) 14
- MFX-1600/1700 15
- Connection Diagram (1/2) 15
- 2.2 Main Control PCB 17
- GENERATOR 19
- 2.4 Power Supply Unit (PSU) 20
- 2.5 Sensors 21
- 2.5.2 Sensor Descriptions 22
- 2.6.1 Document Detection 23
- 2.6.2 Document Separation 23
- 2.6.3 Document Transport 23
- 2.6.4 Document Scanning 23
- 2.6.5 Document Discharge 24
- 2.7 Recording Section 25
- 2.8 Image Processing 25
- Toner agitator 26
- Toner supply roller 26
- Developing roller 26
- Hight voltage unit + output 27
- Eraser brush 27
- 2.8.6 Fusing 28
- MFX-1300/MFX-1200: 29
- Post card printing only 29
- Section3 31
- Adjustment Procedures 31
- Machine Parameter A:0 33
- Machine Parameter A:1 33
- Machine Parameter A:2 34
- (MFX-1700/MFX-1600) 35
- (MFX-1300/MFX-1200) 35
- (MFX-1700/MFX-1600) 35
- (MFX-1300/1200) 36
- (MFX-1300MFX-1200) 37
- (MFX-1700/1600) 38
- (MFX-1300-1200) 38
- Machine Parameter B:7 39
- Machine Parameter B:8 39
- Machine Parameter B:9 ∼ 39
- ∼ C:9 --- Factory use only 39
- Machine Parameter D:0 40
- Machine Parameter D:1 40
- Machine Parameter D:2 40
- Machine Parameter D:3 40
- Machine Parameter D:4 41
- Machine Parameter D:5 41
- Machine Parameter D:6 41
- Machine Parameter D:7 41
- Machine Parameter G:6 44
- Machine Parameter G:7 44
- Machine Parameter H:0 44
- Machine Parameter J:0 46
- Machine Parameter J:1 46
- Machine Parameter J:2 46
- Machine Parameter J:3 47
- Machine Parameter J:4 47
- Machine Parameter J:5 ∼ 47
- ∼ J:9 --- Factory use only 47
- 3.3 Memory Switch Adjustment 48
- Memory Switch A:0 - Dialer 49
- Memory Switch A:1 - Dialer 49
- Memory Switch A:2∼ 49
- ∼ A:4 --- Factory use only 49
- Memory Switch A:5 - Dialer 50
- Memory Switch A:6 ∼ 50
- ∼ A:9 --- Factory use only 50
- Memory Switch B:7 ∼ 54
- ∼ B:9 --- Factory use only 54
- Memory Switch C:2 ∼ 55
- Memory Switch D:4 ∼ 57
- ∼ D:9 --- Factory use only 57
- Memory Switch E:0 - Scanner 58
- Memory Switch E:1 ∼ 58
- ∼ F:9 --- Factory use only 58
- Memory Switch H:3 ∼ 65
- 3.5 All RAM Clear 66
- 3.7 Unique Switch Adjustment 70
- Unique Switch c:4 ∼ 75
- ∼ c:9 --- Factory use only 75
- Unique Switch d:0 - Modem 76
- Unique Switch d:1 - Modem 76
- Unique Switch d:2 - Modem 77
- Unique Switch d:4 77
- Unique Switch d:5 78
- Unique Switch d:6 - Modem 78
- Unique Switch e:2 - Scanner 80
- Unique Switch e:4 - Scanner 80
- Unique Switch e:5 - Scanner 81
- Unique Switch e:6 - Scanner 81
- Unique Switch e:7 - Scanner 82
- Unique Switch e:8 - Scanner 82
- (MFX-1300) 83
- (MFX-1700) 83
- Unique Switch f:0 - Printer 84
- Unique Switch f:1 - Printer 84
- Unique Switch f:2 - Printer 85
- Unique Switch f:3 ∼ 85
- ∼ f:4 --- Factory use only 85
- Unique Switch f:5 - Printer 85
- Unique Switch f:6 - Printer 86
- Unique Switch f:7- Printer 86
- Unique Switch g:1 ∼ 87
- ∼ g:6 --- Factory use only 87
- Unique Switch g:8 ∼ 88
- ∼ g:9 --- Factory use only 88
- Unique Switch h:5 ∼ 90
- ∼ i:6 --- Factory use only 90
- 100% 50% 200% 91
- 3.8 Printer maintenance mode 93
- 3.9 Print Program Mode List 94
- 3.10 Test Modes 94
- 3.10.1 Life Monitor 95
- 3.10.2 Printer Test 96
- 3.10.3 Feeder test 97
- 3.10.4 Background Level Test 97
- 3.10.5 Set Background Level 97
- Unique Switch Settings 98
- 3.12 Factory Functions 98
- 3.12.3 LCD Test 99
- 3.12.4 Key Panel Test 99
- 3.12.5 SRAM Check 100
- 3.12.6 DRAM Check 100
- 3.12.8 RS-232C Test 101
- 3.13 Line Tests 102
- 3.13.2 Tonal Signal Test 103
- 3.13.3 DTMF Output Test 106
- Mirror Locked :On 107
- 107
- / /Enter 107
- 3.15 Consumable order sheet 108
- LCD will show: 109
- 3.16 DRAM Clear 111
- 3.17 Clear Life Monitor 111
- 3.18 Clear Optional Data 112
- 3.19 Set Service Code 112
- Service report settings 120
- 3.22 JP1, JP2 Battery Backup 122
- 3.23 Update the software 122
- Section4 123
- Troubleshooting Procedures 123
- 4.2 Recording Paper Jam 124
- 4.3 Document Feeder Jam 124
- 4.5 Mirror Carriage Error 125
- 4.6 Transmit Error 125
- 4.7 Transmit Black Lines 125
- 4.8 Cannot transmit 126
- 4.9 Receive Errors 126
- 4.10 Will not Auto-Answer 126
- 4.11 Clearing Jammed Paper 127
- To remove the document: 128
- 4.12.1 Blank pages 131
- 4.12.2 Black pages 131
- 4.12.3 Printout too light 132
- 4.12.4 Printout too dark 132
- 4.12.5 Blurred background 132
- 4.12.6 Uneven print density 133
- 4.12.7 Irregularities 133
- 4.12.8 White (Black) Line 134
- 4.12.9 Toner Smudges 134
- 4.13 LCD Error Messages 135
- PAPER SIZE 138
- 4.14 Error Codes 140
- Transmission errors 141
- Communication Error Messages 142
- 4.15 Service Call Error 143
- RX Motor Error 145
- Drum Fuse Error 145
- H-Vlt Fuse Disconnect 145
- 4.16 LCD Failure 146
- 4.17 General Power Failure 146
- 4.18 Cleaning the Unit 147
- Cleaning the LED print head 148
- Section5 149
- Maintenance & Adjustment 149
- 5.1 Maintenance schedule 150
- 5.2 Re/Disassemble 151
- 5.2.1 Covers 153
- FRONT COVER 154
- REAR COVER 154
- TOP REAR COVER 155
- HARNESS HOLDER 155
- Tx cover 156
- Tx side cover F 156
- Tx side cover R 157
- Exit tray 157
- Option cover A 158
- Rx exit cover 158
- Rx exit cover A 158
- Rx exit cover B 158
- Right cover 159
- Line cover 159
- Cover opener 159
- Cover lever 159
- PANEL COVER 160
- PLATEN COVER 160
- BOTTOM CORNER COVER 160
- BYPASS TRAY 160
- 5.2.2 PCBs 161
- Shield plate 162
- Main control PCB 162
- NCU PCB 163
- MODULAR PCB 163
- POWER SUPPLY UNIT (PSU) 164
- CONNECT PRINTER PCB 165
- Film harness of the LCD 166
- Bottom corner cover 167
- Hinge screw 167
- BATTERY PCB 169
- Inverter PCB 170
- Lens cover 170
- Connect ADF PCB 171
- Ground wire 171
- 5.2.3 Sensors 172
- 5.2.4 Scanning section 173
- TXIL(ADF) 174
- Separator gear 22 174
- Separator roller assembly 174
- Retard cover 175
- Retard roller assembly 175
- Torque limiter 175
- Motor bracket 176
- Spring C 176
- Pulley 50/17 G26 176
- Pulley 17 176
- Inner guide A assembly 176
- Feed roller A 177
- APS bracket 177
- APS feeler 177
- FEED ROLLER B 178
- Exit gear 24 179
- Platen sheet 179
- Platen stay B 180
- Exit roller 180
- HOME SENSOR / END SENSOR 181
- FBS MOTOR 181
- Ground plate 182
- Belt retainer 183
- Flat cable 183
- Cover switch 185
- Solenoid 186
- Rx motor 186
- Drive gear assembly 187
- Pick up roller MP 188
- Image transfer roller 189
- PDS / Thermistor 190
- EXIT ROLLER P 190
- Paper pick up roller 191
- Feed roller BP 192
- MP bracket 192
- FEED ROLLER AP 193
- Press spring B 194
- Release lever 194
- Press roller BP 194
- PSS cover 194
- LED print head 195
- Bypass tray 196
- 5.3 Adjustment 197
- Section 6 199
- Options 199
- PHONE1PHONE2 201
- 6.3 RS-232C interface 202
- RS-232C interface cable 204
- Signal direction 204
- RS-232C Test 204
- Packaging contents: 205
- Installation 205
- 6.4 AL-200 206
- (only for MFX-1700/MFX-1600) 206
- Modular PCB 207
- 6.5 OP-100/NP-200 210
- Option cover B 213
- EtherNet port Network cable 214
- 6.6 Attaching the 2-Bin tray 215
- PCB shield 215
- Printer connect PCB 215
- RX exit cover A 216
- <References> 217
- 6.7 Second paper cassette 220
- 3x10mm screws 222
- Setting of the Paper Size 223
- Access cover 225
- 6.Attacht the module box 226
- Copy/Fax/Scan label 230
- Soft key label 230
Related products and manuals for Multifunctionals Muratec MFX-1700
Multifunctionals Muratec MFX-2350 User Manual
(164 pages)
(164 pages)
Multifunctionals Muratec F-315 User's Guide
(198 pages)
(198 pages)
Multifunctionals Muratec MFX-1330 Specifications
(290 pages)
(290 pages)
Multifunctionals Muratec MFX-3530 Specifications
(130 pages)
(130 pages)
Multifunctionals Muratec MFX-2500 Specifications
(453 pages)
(453 pages)
Multifunctionals Muratec F-320 User's Guide
(122 pages)
(122 pages)
Multifunctionals Muratec F-565 User's Guide
(204 pages)
(204 pages)
© 2020, manymanuals.com. All rights reserved. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals