Muratec MFX-1330 Specifications Page 186
- Page / 290
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-24
The errors messages and an explanation of each are outlined below.
RX Motor Error
Suggested corrective action:
1. Check the connection between RX motor and the Connect A PCB (P90). (See page 2-1.)
2. Verify the RX motor rotates when the power is on. If OK, see step 6.
3. Check the power is supplied to the Rx motor. If it does not, see step 5.
4. Replace the RX motor if it doesn’t rotate.
5. Replace the Connect A PCB.
6. If the problem is not correct, replace the main control board.
Fan Error
Suggested corrective action:
1. Verify the inside fan rotates when the power is on.
2. Check the connection between the fan and Connect A PCB(P87), Connect A PCB (P80C) and the
main board.
3. Replace the fan motor if it doesn’t rotate.
4. Replace the Connect A PCB.
5. Replace the main control board.
Fuser Error
Suggested corrective action:
1. Turn on the power again, and verify the fuser warms up. If it does not, see step 4.
2. Check the contact between Fusing thermistor and Connect A PCB(P89).
3. Check the contact between Connect A PCB (P80C) and the main board.
4. Replace the Fuser.
5. After replacing the Fuser, verify the fuser warms up when the power is on.
6. Replace the main control PCB.
Drum Error
Suggested corrective action:
1. Verify the drum cartridge is set correctly.
2. Check the point of contacts between drum cartridge and Connect A PCB (P86)．
3. Check the contact between Connect A PCB (P80C) and the main board.
4. Replace the drum cartridge.
5. Replace the Connect A PCB.
6. Replace the main control PCB.
- Muratec 1
- MFX-1330 / F-300 1
- Safety Information 3
- Table of Contents 5
- Section 1 9
- General Description 9
- 1.2 Specifications 10
- 446 mm (H) 12
- 566 mm (H) 12
- Section2 13
- Machine Composition 13
- 2.2 Main Control PCB 15
- 2.4 Power Supply Unit (PSU) 17
- 2.5 Sensors 18
- 2.5.2 Sensor Descriptions 19
- 2.6.1 ADF Detection 20
- 2.6.1.2 Original Detection 21
- 2.7 Recording Section 23
- 2.8 Image Processing 24
- 2.8.3 Development 25
- 2.8.4 Image Transfer 25
- 2.8.5 Erasing 26
- 2.8.7 Fusing 27
- Main Control PCB 28
- Power supply unit 28
- AC Inlet 28
- Fusing unit 28
- Section3 29
- Adjustment Procedures 29
- Machine Parameter 007 32
- Machine Parameter 010 32
- Machine Parameter 011 33
- Machine Parameter 012 33
- Machine Parameter 013 34
- Machine Parameter 014 34
- Machine Parameter 015 35
- Machine Parameter 016 35
- Machine Parameter 017 36
- Machine Parameter 018 36
- Machine Parameter 020 37
- Machine Parameter 021 37
- Machine Parameter 025 38
- Machine Parameter 030 39
- Machine Parameter 031 39
- Machine Parameter 032 39
- Machine Parameter 033 40
- Machine Parameter 034 40
- Machine Parameter 090 41
- Machine Parameter 091 41
- Machine Parameter 100 42
- Machine Parameter 101 42
- Machine Parameter 107 42
- Machine Parameter 108 43
- Machine Parameter 140 43
- Machine Parameter 141 43
- Machine Parameter 147 44
- Machine Parameter 148 44
- Machine Parameter 160 44
- Machine Parameter 161 45
- Machine Parameter 167 45
- Machine Parameter 168 45
- Machine Parameter 180 47
- Machine Parameter 181 47
- Machine Parameter 187 48
- Machine Parameter 188 48
- Machine Parameter 220 49
- Machine Parameter 221 49
- Machine Parameter 227 50
- Machine Parameter 228 50
- Machine Parameter 240 51
- Machine Parameter 241 51
- Machine Parameter 247 52
- Machine Parameter 248 52
- Machine Parameter 285 53
- Machine Parameter 286 53
- Machine Parameter 287 54
- Machine Parameter 288 54
- Machine Parameter 289 55
- Machine Parameter 460 55
- Machine Parameter 461 56
- Machine Parameter 462 56
- Machine Parameter 463 57
- Machine Parameter 464 57
- Machine Parameter 465 58
- Machine Parameter 466 58
- Machine Parameter 467 59
- Machine Parameter 468 59
- Machine Parameter 469 60
- Machine Parameter 470 60
- Machine Parameter 471 61
- Machine Parameter 472 61
- Machine Parameter 473 62
- Machine Parameter 474 62
- Machine Parameter 475 63
- Machine Parameter 476 63
- Machine Parameter 477 64
- Machine Parameter 478 64
- Machine Parameter 479 65
- Machine Parameter 480 65
- Machine Parameter 481 66
- Machine Parameter 482 66
- Machine Parameter 483 67
- Machine Parameter 484 67
- Machine Parameter 485 68
- Machine Parameter 486 68
- Machine Parameter 487 69
- Machine Parameter 488 69
- Machine Parameter 489 70
- Machine Parameter 490 70
- Machine Parameter 492 71
- Machine Parameter 493 72
- Machine Parameter 494 73
- Machine Parameter 495 74
- 3.3 Memory Switch Adjustment 76
- Memory Switch 00 - Dialer 77
- Memory Switch 01 - Dialer 78
- Memory Switch 20 - Reception 84
- Memory Switch 21 - Reception 84
- Memory Switch 23 - Reception 85
- Memory Switch 30 - Modem 85
- Memory Switch 31 - Modem 86
- Memory Switch 32 - Modem 86
- Memory Switch 33 - Modem 87
- Memory Switch 40 - Scanner 88
- Memory Switch 70 - Operation 94
- Memory Switch 71 - Operation 95
- Memory Switch 72 - Operation 96
- 3.5 All RAM Clear 97
- 3.7 Unique Switch Adjustment 102
- Unique Switch 00 — Dialer 103
- Unique Switch 01 — Dialer 103
- Unique Switch 20 - Reception 107
- Unique Switch 21 - Reception 107
- Unique Switch 23 - Reception 108
- Unique Switch 22 - Reception 108
- Unique Switch 30 - Modem 109
- Unique Switch 31 - Modem 109
- Unique Switch 32 - Modem 110
- Unique Switch 34 - Modem 110
- Unique Switch 37 - Modem 111
- Unique Switch 41 112
- Unique Switch 44 112
- Unique Switch 48 - Scanner 113
- Unique Switch 49 - Scanner 114
- Unique Switch 50 - Printer 115
- Unique Switch 52 - Printer 115
- Unique Switch 53 — Printer 116
- Unique Switch 70 - Operation 119
- Unique Switch 71 - Operation 119
- Unique Switch 72 - Operation 120
- Unique Switch 73 - Operation 120
- Unique Switch 74 - Operation 121
- Unique Switch 77 - Operation 121
- Unique Switch 78 - Operation 122
- Unique Switch 79 - Operation 122
- 3.10.1 Life Monitor 127
- 3.10.2 Printer Test 128
- 3.10.3 Feeder test 129
- 3.10.4 Port Status 129
- 3.10.5 Set Background Level 129
- Unique Switch Settings 130
- 3.12 Factory Functions 130
- 3.12.3 LCD Test 131
- 3.12.4 Key Panel Test 131
- 3.12.5 SRAM Check 132
- 3.12.6 DRAM Check 132
- 3.12.8 Page memory check 133
- 3.12.9 Generate bell test 133
- 3.13.1 Relay Test 134
- 3.13.2 Tonal Signal Test 134
- 3.13.3 DTMF Output Test 136
- 3.15 Consumable order sheet 138
- LCD will show: 139
- 3.21 Sensor input test 144
- 3.22 Printer diagnostic mode 145
- 3.23 Network service mode 145
- 3.24 Multi Line Settings 146
- 3.25 Flash Rom Sum Check 147
- 3.27 Set Service Report 147
- 3.27.2 Clear service report 148
- 3.28 Quick Initial settings 149
- 3.28 Update the software 155
- Error code 161
- Section4 163
- Troubleshooting Procedures 163
- 4.2 Recording Paper Jam 164
- 4.3 Document Feeder Jam 164
- 4.6 Transmit Error 165
- 4.7 Transmit Black Lines 165
- 4.8 Cannot transmit 166
- 4.9 Receive Errors 166
- 4.10 Will not Auto-Answer 166
- 4.11 Clearing Jammed Paper 167
- To remove the document: 168
- Jammed in feed area 169
- Jammed in exit area 169
- Jammed in fuser area 171
- Jammed in paper exit area 171
- 4.12.1 Blank pages 173
- 4.12.2 Black pages 173
- 4.12.3 Printout too light 174
- 4.12.4 Printout too dark 174
- 4.12.5 Blurred background 174
- 4.12.6 Uneven print density 175
- 4.12.7 Irregularities 175
- 4.12.8 White (Black) Line 176
- 4.12.9 Toner Smudges 176
- 4.13 LCD Error Messages 177
- STOP to cancel a print job 179
- 4.14 Error Codes 182
- Transmission errors 183
- Communication Error Messages 184
- 4.15 Service Call Error 185
- RX Motor Error 186
- Fan Error 186
- Fuser Error 186
- Drum Error 186
- Developer Error 187
- 4.16 LCD Failure 188
- 4.17 General Power Failure 188
- 4.18 Cleaning the Unit 189
- Document glass 190
- ADF glass 190
- Document pad 190
- Section5 191
- Maintenance & Adjustment 191
- 5.1 Maintenance schedule 192
- 5.2 Re/Disassemble 193
- 5.2.1 COVERS 195
- Tray document 196
- Cover CONNECT 196
- PCB CONNECT A 196
- COVER PLATEN (MFX-1330 only) 197
- COVER ADF BASE (F-300 only) 197
- Cover TX side B 198
- Guide outer 198
- Cover Tx side F 200
- COVER TX SIDE F (F-300) 201
- COVER FRONT 202
- TRAY EXIT PAPER 202
- COVER PANEL (MFX-1330) 203
- COVER PANEL (F-300) 203
- TRAY A MP/PAD FLAPPER MP 204
- 5.2.2 PCBS 205
- H(See page 5-13)H 206
- PCB INVERTER 207
- HH(See page 5-17)HH 209
- HH(See page 5-6)HH 210
- HH(See page 5-20)HH 211
- HHH(See page 5-20)HHH 211
- POWER-SUPPLY 211
- HHH(See page 5-32)HHH 213
- HHH(See page 5-12)HHH 213
- HHH(See page 5-8)HHH 214
- HHH(See pageHHH 5-35) 215
- Roller feed 216
- HHHH(See pageHHH 5-35)H 217
- HHHH(See pageHHH 5-255-25)H 217
- FRAME SCANNER (MFX-1330) 218
- Shaft guide 219
- Frame scanner 219
- Flat harness 220
- Bracket scanner B 220
- HHHH(See page 5-7)HHHH 221
- HHHH(See page 5-13)HHHH 221
- HHHH(See page 5-28)HHHH 221
- Sensor stopper 221
- Home sensor 221
- HHHH(See page 5-6)HHHH 222
- HHHHH(See page 5-20)HHHHH 222
- HHHHHH(See page 5-20)HHHHHH 222
- ADF motor 223
- Bracket motor ADF 223
- Cable tie 224
- Guide inner A 225
- Ground wire 225
- APS bracket 225
- Pad separator 226
- Cover separator 226
- ADF DRIVE GEARS 227
- Guide inner B 229
- FBS MOTOR (MFX-1330 only) 230
- FBS motor 231
- 5.2.4 PRINTER SECTION 232
- RX motor 233
- SPRING CLUTCH 234
- FRAME DRIVE GEARS 235
- ROLLER TRANSFER 237
- Roller transfer 238
- Bracket transfer 238
- Chassis cassette 2nd 239
- Feeler MP 239
- H (See page 5-20)H 240
- H (See page 5-32)H 240
- SENSOR PSS 241
- Pad pressure MP 242
- Guide paper MPDUP 242
- THERMISTOR/ THERMO 243
- H (See page 5-52)H 244
- ROLLER PRESS 245
- SENSOR PDS / DPS 246
- ROLLER EXIT 246
- Cassette 1st 247
- Roller pick up 247
- SENSOR JAMC2 248
- Plate frame F 249
- Guide paper 2nd CST 249
- Roller feed 2nd 249
- PLATE FRAME B (2nd CST) 250
- Holder gear 2ND 252
- Spring clutch 252
- Plate frame B 252
- Solenoid 252
- Chassis 2nd 253
- Guide upper JAC 254
- Cover jam access 254
- Roller feed duplex A 255
- Knob pressure 256
- Toner cartridge 256
- Drum cartridge 256
- Bracket toner sensor B 257
- Bracket toner sensor A 258
- Bracket sensor 259
- H(See page 5-20)H 260
- Film harness 261
- 5.3 Adjustment 262
- Test pattern H 263
- Adjustment procedure 265
- 5.3.9 FBS registration (top) 269
- Roller separator 273
- Mirror A 274
- Mirror C 274
- Mirror B 274
- Cover scanner 274
- Cover top 275
- Cover contact A 275
- Sheet document press 275
- Section 6 Options 277
- 6.2 Second paper cassette 279
- 6.3 Page Counter 281
- Connection board B 282
- Relay cable 282
- 6.4 PCL printer controller 283
- 6.5 Network interface board 284
- 6.6 Second phone line kit 287
Related products and manuals for Multifunctionals Muratec MFX-1330
Multifunctionals Muratec MFX-3530 Specifications
(130 pages)
(130 pages)
Multifunctionals Muratec MFX-2500 Specifications
(453 pages)
(453 pages)
Multifunctionals Muratec F-320 User's Guide
(122 pages)
(122 pages)
Multifunctionals Muratec F-565 User's Guide
(204 pages)
(204 pages)
Multifunctionals Muratec F-565 Specifications
(383 pages)
(383 pages)
Multifunctionals Muratec F-525 User's Guide
(40 pages)
(40 pages)
© 2020, manymanuals.com. All rights reserved. | 0.171 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals